Installation Instructions for WH111: Hauff/Chinook PV101

Make: Chinook/HF Hauff

Engine: Ford V-10

Autostart: Multiple, PV101 for Gauges

Altrac Wiring Harness: WH111

Installation Video link

https://youtu.be/AeGwIGOt_mY

Learn how to install the Altrac wiring harness for the engine below.  Once installed, the Altrac Station will have access to power as well as readings from various sensors on the engine. 

WH111

Key	Wire Color	Purpose	Terminal Type	Installation
A	Multiple	Control Line Connector	12-Pin Deutsch Connector	Plug into the matching 12-pin connector on the ST100's control line.
B	Multiple	Accessory Port	6-Pin Deutsch Connector	Attach additional sensors such as fuel level or soil moisture.
C	Multiple	PV101 Connection	6-Pin Deutsch Connector	Attach to port B on the PV101 gauge panel.
D	Multiple	Controls the wind machine.	Relay	Mount near the gauge panel with a self-tapping screw.
E	Red	Battery Voltage (12VDC)	Quick Connect Male	Connect to bottom-middle contact on Manual-Off-Auto switch (red wire).
F	Red	Battery Voltage (12VDC)	Quick Connect Female	Connect to bottom-middle contact on Manual-Off-Auto switch (red wire).
G	Black	Ground	Quick Connect Male	Connect to middle contact on RPM rocker switch (green wire).
H	Black	Ground	Quick Connect Female	Connect to middle contact on RPM rocker switch (green wire).
I	Yellow	Call to Start	5mm Bullet Connector	Insert into the trailer connector (matching yellow wire).
J	Brown	Auto Position Detection	Quick Connect Male	Connect to the 'Auto' side of the Manual-Off-Auto switch (brown wire).
K	Brown	Auto Position Detection	Quick Connect Female	Connect to the 'Auto' side of the Manual-Off-Auto switch (brown wire).

Tool List

Use	Tool
Wiring Harness Installation	Philips Screwdriver - Medium
Wiring Harness Installation	Philips Screwdriver - Large
Wiring Harness Installation	Flathead Screwdriver - Large
Wiring Harness Installation	Magnetic Bolt Retriever
Wiring Harness Installation	Channel Locks
Wiring Harness Installation	Electrical Tape
Wiring Harness Installation	4" Zip Ties
Wiring Harness Installation	12" Zip Ties
Wiring Harness Installation	18" Zip Ties
Wiring Harness Installation	Nippers (Flush Cutters)
Wiring Harness Installation	Adjustable Cresent Wrench
Wiring Harness Installation	Socket Drivers
Wiring Harness Installation	Wire Strippers
Wiring Harness Installation	Crimpers for Butt Connector
Wiring Harness Installation	Butt Connector (Blue)
Device Mounting	Impact Driver/Drill
Device Mounting	Metric Socket Set for Drill
Device Mounting	Drill Bits and Drivers
Device Mounting	Ladder
Device Mounting	Body Harness

Installation Instructions 

Before you attempt a wiring harness installation, you must unhook the wind machine battery and turn the Manual-Off-Auto switch to the OFF position. 

Step 1

Disconnect the wind machine 12V battery.

Step 2

Connect the black ground wires to the ground source on the engine. Remove the green wire from the middle contact on the RPM rocker switch and jump it with the two black wires on the Altrac wiring harness.

Step 3

Connect red power wire to bottom-middle contact on the Manual-Off-Auto switch. Remove the red wire and jump it with the two red wires on the Altrac wiring harness.

Step 4

Connect the brown auto position detect wire to the auto side (left) of the Manual-Off-Auto switch. Remove the brown wire from the auto side of the switch and jump it with the two brown wires on the Altrac wiring harness.

Step 5

Connect the grey 6-pin connector to the open slot ‘B’ on the back of the PV101.

Step 6

Connect the yellow call to start wire to the yellow wire in the tailer connector on the wind machine engine. This trailer connector is usually plugged into the existing temperature probe controller.

Step 7

You must program the PV101 to send gauge readings to the Altrac Station. To start, turn the Manual-Off-Auto switch to Manual to power up the PV101.

Step 8

Press the Menu button (three dots + lines) and select ‘Utilities’.

Step 9

Select ‘OEM’.

Step 10 

Enter Password. The default password is ‘3482’.

Step 11

Select ‘ModBus Setup’.

Step 12

Select ‘Slave Active’. Once you have selected ‘Slave Active’ you can close the menu and return to the main page.

Step 13

Reattach the wind machine battery.

Step 14

Connect the new wiring harness to the Altrac Station via the 12-pin connector on the control line.

HINT: You should tuck the connector up under the wind machine hood when you are finished installing to maximize weather protection.

Step 15

Connect temperature probe and any other sensors to appropriate connections.